Concepts of Chemical Engineering 4 Chemists

Herausgeber: Simons, Stefaan

• Gebundenes Buch

Produktbeschreibung

Designed as a reference guide, this book is fully illustrated with worked examples, extensive reference and bibliography sections.

Produktdetails

• Verlag: Royal Society of Chemistry
• Seitenzahl: 370
• Erscheinungstermin: 27. März 2007
• Englisch
• Abmessung: 242mm x 162mm x 26mm
• Gewicht: 708g
• ISBN-13: 9780854049516
• ISBN-10: 0854049517
• Artikelnr.: 22767285

Autorenporträt

The Author Professor Simons is a Chartered Engineer and Fellow of the Institution of Chemical Engineers (IChemE) and is a member of the Executive Committee of the Standing Conference of Chemical Engineering Professors. He is also vice-chair of the committee of the IChemE's Particle Technology Subject Group and serves on the committee of the Royal Society of Chemistry's Process Technology Group, which initiated the short course on which this book is based. Professor Simons' expertise lies in particle technology, in general, and, more specifically, in the development of low carbon technologies in regards to the reduction of carbon dioxide emissions, particularly in carbon capture and storage, for which he was an expert reviewer of the Intergovernmental Panel on Climate Change's special report on this subject.

Inhaltsangabe

Chapter 1: Process Analysis - The Importance of Mass and Energy Balances
1.1: Introduction 1
1.1.1: Nomenclature and Units of Measurement 1
1.2: Mass Balances 3
1.2.1: Process Analysis Procedure 4
1.2.2: Example 1: Mass Balance on a Continuous
Distillation Process
1.2.3: Example 2: Mass Balance on a Process with Reaction
1.3: Energy Balances
1.3.1: Example 3: Energy Balance on a Distillation Column
1.4: Summary
Recommended Reading
Chapter 2: Introduction to Chemical Reaction Engineering
2.1: Introduction
2.1.1: Classification of Reactors
2.2: Chemical Reaction Kinetics
2.2.1: Definitions
2.2.2: Chemical Reaction Thermodynamics
2.2.3 Kinetics
2.2.4: Importance of Mass and Heat Transfer Processes
2.2.5: Kinetics of a Catalytic Reaction
2.3: Concepts of Chemical Reactor Design
2.3.1: Mole Balances for Chemical Reaction
2.3.2: Reactor Design Equation
2.3.3: Comparison between Continuous Stirred Tank
Reactor and Plug Flow Reactor
2.3.4: Recycle Reactor
2.3.5: CSTRs in Series
2.3.6: Multiple Reactions
2.3.7: PFR with Continuous Uniform Feed of Reactant along the Whole Reactor
Recommended Reading
Chapter 3: Concepts of Fluid Flow
3.1: Introduction
3.2: Dimensionless Groups
3.2.1: Example: Pipe Flow
3.3: Viscosity
3.3.1 Newton's Law of Viscosity
3.3.2: Dynamic and Kinematic Viscosity
3.3.3: Typical Values of Viscosity
3.4: Laminar and Turbulent Flow
3.4.1: Boundary Layers
3.5: Balance or Conservation Equations
3.5.1: General Form of the Conservation Equations
3.5.2: Control Volumes
3.5.3: Continuity Equation (Mass Balance)
3.5.4: Steady-State Momentum (Force) Balance Equation
3.5.5: Steady-State Energy Balances
3.5.6: Example of use of the Conservation Equations
3.6: Pipe Flow
3.6.1: Friction Factors
3.6.2: Losses in Fittings 70
3.6.3: Economic Velocities
3.7: Flow Measurement
3.7.1: Variable Head Meters
3.7.2: Variable Area Meters
3.7.3: Some Other Flowmeters
3.8: Pumps and Pumping
3.8.1: Positive Displacement Pumps
3.8.2: Non-Positive Displacement Pumps
3.8.3: Matching Centrifugal Pumps to Flow Requirements
3.8.4: Pump Power Requirements
3.9: Other Flows
3.9.1: Equivalent Hydraulic Diameter
3.9.2: Flow Around Bodies
3.9.3: Stirred Tanks
3.10: Example Calculations for the Pipe-Flow System
3.10.1: Data
3.10.2: Friction Losses
3.10.3: Orifice Meter
3.10.4: Pump Shaft Work
3.10.5: System Head
3.10.6: Pump Characteristics
3.10.7: Control Valve
3.10.8: Net Positive Suction Head
Nomenclature
References
Chapter 4: An Introduction to Heat Transfer
4.1: Introduction and Objectives
4.1.1: Modes of Heat Transfer
4.1.2: Scope and Objectives
4.2: Modes of Heat Transfer: 4.2.1: Conduction
4.2.2: Convection
4.2.3: Radiation
4.3: The Overall Heat Transfer Coefficient, U
4.3.1: Example Calculation of U
4.3.2: Overall Heat Transfer Coefficients with Curvature, for Example, Transfer through a Pipe Wall
4.3.3: Overall Heat Transfer Coefficients with Convection and Radiation
4.4: Transient Heat Transfer
4.4.1: Example Calculation, Small Bi Case: Cooling of a Copper Sphere in Air
4.4.2: Example Calculation, Large Bi Case: Cooling of a Perspex Plate in Water
4.5: Heat Exchangers
4.5.1: Double Pipe Heat Exchanger
4.5.2: Heat Transfer in Heat Exchangers
4.5.3: Performance of Heat Exchangers - Fouling
4.5.4: Types of Heat Exchangers
4.5.5: Numerical Examples
4.6: Conclusions
Nomenclature
References
Chapter 5: An Introduction to Mass-Transfer Operations
5.1: Introduction
5.2: Mechanisms of Separation
5.3: General Separation Techniques
5.3.1: Separation by Phase Addition or Phase Creation
5.3.2: Separation by Barrier
5.3.3: Separation by Solid Agent
5.4: Mass Transfer Calculations
5.4.1: Equilibrium-Stage Processes
5.4.2: Stage Calculations
5.4.3: Graphical Methods
5.4.4: Diffusional Rate Processes
5.4.5: Diffusion Calculations
5.5: Separation by Distillation
5.5.1: Trays and Packing
5.5.2: Design Range
5.5.3: Operating Range
5.5.4: Design Calculations
5.5.5: Distillation Column Height
5.6: Separation by Absorption
5.6.1: Design Range
5.6.2: Operating Range
5.6.3: Design Calculations
5.6.4: Amount of Solvent
5.6.5: Absorption Column Height
5.7: Further Reading
5.8: Relevant Material not Considered in this Chapter
5.8.1: Combined Reaction and Separation
5.8.2: Combined Separation Units
5.8.3: Batch Operation
References
Chapter 6: Scale-Up in Chemical Engineering
6.1: Introduction and Objectives
6.2: Units and Fundamental Dimensions
6.3: Physical Similarity
6.3.1: Geometric Similarity
6.3.2: Dynamic Similarity
6.3.3: Dimensionless Groups
6.4: Dimensional Homogeneity
6.5: Dimensional Analysis and Dimensionless Groups
6.5.1: Example: Dimensional Analysis
6.6: Buckingham Pi Theorem and Method
6.6.1: Buckingham Pi Theorem
6.6.2: Buckingham's Method - Procedure
6.6.3: Example: Drag Force on a Sphere
6.7: Use of Dimensionless Groups in Scale-Up
6.7.1: Drag Force on a Particle
6.7.2: Pressure Drop in a Pipe
6.7.3: Modelling Flow Around a Body Immersed in a Fluid
6.7.4: Heat Transfer
6.7.5: Mass Transfer
6.7.6: Correlation of ExperimentalData - Formation of Gas Bubbles at an Orifice
6.7.7: Application of Scale-Up in Stirred Vessels
6.7.8: Incompatibility of Some Equations
6.8: Conclusions
Nomenclature
References